Pickup Hex Bearing with Flangettes Deere Models 336, 346, 327, 337, 347, 328, 338, 348
$129.99
Pickup arm bearing. New John Deere Baler OEM Part # AE28843
$129.99
John Deere Model 328, 338, 348 Parts
-
-
Good Used Front Clutch Plate for John Deere Models 24, 224, 336, 346, 327, 337, 347, 328, 338, 348
$199.99Good used, tech-certified John Deere OEM Part #E38906 and #E57134
$199.99 -
Drawbar Support Frame for John Deere Model 336, 346 ,327, 337, 347, 328, 338, 348
$799.99John Deere OEM Part #BE32440. Includes bolt and bushing. Needed for drawbar installation. (SUB FOR AE27318, AE30988 OR AE38409)
$799.99 -
Good Used Main Drive Sprocket (behind Slip Clutch) for John Deere Model 336, 346, 327, 337, 328, 338
$42.99Good used John Deere OEM part #E19123 Does not fit on John Deere Models 347 and 348
$42.99 -
OUT OF STOCK- Good Used Primary PTO Shaft & Yoke Assembly with New Cross Bearing for John Deere Model 336, 342, 346, 346WS, 327 337, 347, 328, 338, 348
$299.99Good used John Deere OEM assembly Part #AN104578 (used) and #E55209 (new) cross-bearing. Please provide model number and shaft width measurement (1...
View full details$299.99 -
Intermittent Gear for John Deere Square Baler Models 328, 338, 348
$759.99New John Deere OEM Part #FH312371
$759.99 -
Bearing for Main Drive Chain Idler Sprocket for John Deere Model 24T, 224T, 336, 346, 327, 337, 328, 338
$7.99Bearing for New John Deere OEM part #JD8570 Does not fit on John Deere Models 347 and 348
$7.99 -
Main Drive Chain Idler Sprocket for John Deere Model 336, 346, 327, 337, 328, 338
$92.99Main Drive- New John Deere OEM part #AE13630 Does not fit on John Deere Models 347 and 348
$92.99 -
$0.95
-
Good Used Bare Knotter Frame for John Deere Model 328, 338, 348
$649.99No need to pay big bucks for John Deere OEM parts. This 2 part knotter frame is in good used condition. It's been reconditioned and painted, and t...
View full details$649.99 -
Good Used John Deere Knotter for Models 328, 338, 348
$1,499.99Want a good quality used knotter, but don't want a "pick and pull" unit? We won't go out to a baler graveyard and snag any old knotter that will f...
View full details$1,499.99 -
New OEM 2-Piece Knotter Frame for John Deere Model 328, 338, 348
$599.99John Deere OEM part #AE48451 TECH TIP: If you replace your broken knotter frame, then reinstall excessively worn parts, it could fail again....
View full details$599.99 -
Wire Twist Baler Hook for John Deere Model 326W, 336W, 346W, 327W, 337W, 347W, 328W, 338W, 348W,
$179.99John Deere OEM part #FH312159. Replaces part #E32458
$179.99 -
Rebuilt Wire Needle with New Roller for John Deere Wire Baler model 24W, 224W, 336, 346, 327, 337, 347, 328, 338, 348-VERY LIMITED SUPPLY-CALL BEFORE ORDERING
$195.99Good used rebuilt John Deere OEM part #AFH202538. Ground to remove grooves, Repainted and includes new roller, Fits 24, 224, 336, 346, 327, 337, ...
View full details$195.99 -
Rear Clutch Plate for John Deere Models 24T, 224T, 336, 346, 327, 337, 347, 328, 338, 348
$69.99New Aftermarket part replaces John Deere OEM Part #E38904
$69.99 -
Good Used Needle Guard for John Deere model 336, 346, 327, 337, 347, 328, 338, 348
$49.99Good used John Deere OEM part #E63932
$49.99 -
Side Shield for Late Model John Deere Square Balers 328, 338, 348
$149.99New Aftermarket part #3482- replaces John Deere part #AFH206110. Late models include serial numbers 300,000 and up.
$149.99 -
Auger Bearing Race for John Deere Models Late 328, 338, 348
$27.99New aftermarket part #3510 replaces John Deere OEM part #E50308. Serial number break for part- please call with serial number before ordering.
$27.99 -
Inflatable Pickup Gauge Wheel for John Deere Models 327, 337, 347, 328, 338, 348
$179.99New Aftermarket Part #3329. Replaces John Deere OEM part #AM30591. 16 X 6.50, 2 Ply tire. With grease zert.
$179.99 -
Auger Bearing Race for John Deere Models 336, 346, 327, 337, 347 and early 328, 338, 348
$44.99New aftermarket part #3508 replaces John Deere OEM part #E50308. Serial number break for part- please call with serial number before ordering.
$44.99 -
Good Used RH Spacer for John Deere model 336, 346, 327, 337, 347, 328, 338, 348
$39.99Good used John Deere OEM part #E42318. For use below 3351 (E47949) RH Plunger Guide
$39.99 -
Good Used Top RH Strap Spacer for John Deere model 336, 346, 327, 337, 347, 328, 338, 348
$19.99Good used John Deere OEM part #E44714. For use above E44706 RH Plunger Guide
$19.99 -
Worm Gear Shaft for 24T, 224T, 336, 346, 327, 337, 347, 328, 338, 348
$199.99New John Deere OEM Part #E66556
$199.99 -
Pickup Belt Drive Shield For John Deere Models 336, 346, 327, 337, 347, 328, 338, 348
$119.99Good used OEM part #E41906 for all John Deere Square Baler 6, 7 and 8 series.
$119.99 -
OUT OF STOCK- Good Used Hydraulic Bale Compression Assembly for John Deere Models 336, 346, 327, 337, 347, 328, 338, 348
$1,399.99Includes 2 good used tested cylinders and tested pump- new hoses and oil reservoir. Does not include sprocket-sold separately. Original-style cylin...
View full details$1,399.99 -
Good Used Pitman Arm with New Bushings for John Deere Models 336, 327, 337, 328, 338
$359.99Good used OEM pitman arm part #AE46492, new OEM Pitman Pin Bushing- E15566
$359.99 -
Tucker Finger for John Deere Model 14T, 214T
$54.99New aftermarket part. Replaces John Deere OEM Part #AM2888E
$54.99 -
Tucker Shaft for John Deere Models 328, 338, 348
$129.99New Aftermarket part we've used for years when rebuilding 8 series balers
$129.99 -
$249.99 -
Good Used Inspected Gear Box and Input Shaft (includes New Seals) for John Deere Models 336, 346, 327, 328
$1,899.99Fully inspected and includes 3 new seals- not a "pick and pull" part. Good used OEM part. Call for availability. NOTE: Please contact us for sh...
View full details$1,899.99 -
Large Drive Chain Sprocket for John Deere Model 336, 346, 327, 337, 328, 338 - Good Used Part
$40.99Good used John Deere OEM part #AE26326 (replaces part #AE13630 Does not fit on John Deere Models 347 and 348
$40.99 -
Tucker Shaft Roller (2-pc) for John Deere Model 328, 338, 348
$45.99OEM parts #FH312368 (inner) and #FH312373 (outer)
$45.99 -
Heavy Duty LH Spindle Axle Extension Assembly for Thrower-Equipped Models 336, 327, 337, 328, 338
$489.99New aftermarket part. Includes hub, new bearings, seals and races. Reinforced metal in housing and bolt plate. You’ll receive the assembly fully g...
View full details$489.99 -
Knotter Drive Gear Bushing (set of 2) for John Deere Models 328, 338, 348
$27.99New John Deere OEM part #E15963- set of 2
$27.99 -
Main Drive Front 33 Tooth Sprocket for John Deere model 336, 346, 327, 337, 328, 338
$99.99New aftermarket part, replaces John Deere OEM part #AE26326
$99.99 -
Good Used Side Shield for Late Model John Deere Square Balers 328, 338, 348
$159.99Good used John Deere part #AFH206110. Late models include serial numbers 300,000 and up.
$159.99
The latest (and last, so far) series of John Deere small square balers, Many improvements over the previous models, such as updated tucker finger assembly and 2-piece knotter frame. We carry a large inventory of new aftermarket, new and good-used OEM parts, and updated assemblies.