Angled Pickup Teeth for John Deere Models 336, 346, 327, 337, 347, 328, 338, 348, 466, 467
Narrower gap with angled ends makes hay pickup easier and more efficient. New Aftermarket part replaces John Deere OEM part #AE41833,
Narrower gap with angled ends makes hay pickup easier and more efficient. New Aftermarket part replaces John Deere OEM part #AE41833,
For only $39, you get one session of up to 30 minutes of expert diagnostic service for your baler problem, or installation and aligning/tuning your...
View full detailsWe've reconditioned and repainted it, then thoroughly inspected and labeled Technician Certified-Field✔Ready® TECH TIP: If you replace your ...
View full detailsWant a reliable, expertly rebuilt knotter? You can buy with confidence from Green Baler Parts. Our technicians send the original unit through the...
View full detailsGood used part with intact teeth. We will need the casting number if you've got a 24T or 224T. Replaces OEM #AE39977, #E43434 NEW INTERMITTENT GE...
View full detailsGood used John Deere OEM part #FH304339, BP1600E
Good used John Deere OEM part #BP1673E
We probably won't have any more of these for 2024. Want a good quality used knotter, but don't want a "pick and pull" unit? We won't go out to a b...
View full detailsNew Frame, 90% New Parts Want a reliable, expertly rebuilt knotter? You can buy with confidence from Green Baler Parts After sending the original ...
View full detailsGood used OEM part- #FH312277
Good used OEM pitman arm part #AE46492, new OEM Pitman Pin Bushing- E15566, and new Aftermarket Plunger Pin- 3405 (replaces FH312288)
Good Used Bell Hitch John Deere OEM part #E45675, #AE36748, #AE28354
New aftermarket part, replaces John Deere OEM part #AE13424
Good used OEM parts-BP13373
Replaces John Deere OEM part #AE70115. We take structurally sound OEM original style wiper arm and build up worn areas with weld, grind it to spec,...
View full detailsMade with metal. John Deere OEM part #E41839. Click here if you need pickup teeth also
Good used John Deere OEM part #JD8650 (bearing) and AE32173 (support)
Good used, tech-certified John Deere OEM Part #E38906 and #E57134
Good used John Deere OEM part #AE24019- includes new bushing
Good used John Deere OEM part #E19123 Does not fit on John Deere Models 347 and 348
Good used John Deere OEM #AE49686
Good used John Deere part OEM #E79419 or FH312133
Includes: Good used Tube JD #AE29740 Good used Yoke JD #AE24019 Two Good Used Dog Pins JD #E45811 Two Good Used Dogs JD #E36425 New Aftermarket Cr...
View full detailsSet of 2- Adapts Series 6/7 Knotter Shaft to fit Series 8 Knotter Frame 2-piece bracket. Good used OEM part.
John Deere good used OEM part #AE27423 Picture is representative- actual part may not have JD decal
Good used John Deere OEM assembly Part #AN104578 (used) and #E55209 (new) cross-bearing. Please provide model number and shaft width measurement (1...
View full detailsWant a reliable, expertly rebuilt knotter? You can buy with confidence from Green Baler Parts Our technicians send the original unit through the ...
View full detailsGood used John Deere OEM part #AE14643E
Good Used John Deere OEM #AE34293 * To adapt this wheel to a model 14T, a bushing is needed. Click here
Manually adjust bale compression. Good used John Deere OEM part #E14398, includes OEM part #E20398 (lower spring plug) and #BP1762E (upper spring ...
View full detailsGood used John Deere OEM part #FH304063
Retrofit from JD 336 to fit 14T, 24T and 224T. Compressor rods are curved downward for better hay delivery to auger. Includes (7) Curved Rods #E...
View full detailsGood used John Deere part #E38908
No need to pay big bucks for John Deere OEM parts. This 2 part knotter frame is in good used condition. It's been reconditioned and painted, and t...
View full detailsWant a good quality used knotter, but don't want a "pick and pull" unit? We won't go out to a baler graveyard and snag any old knotter that will f...
View full detailsOur technicians go over each part thoroughly to make sure it's structurally sound and still has a lot of usable life in it. If it doesn't, we don't sell it. But if it does, we certify it Field Ready!
TECH TIP: If you replace your broken knotter frame, then reinstall excessively worn parts, it could fail again. Send in your knotter for a complete diagnostic, and we'll replace and repair the necessary components to help prevent it from happening again. Click here for more info |